The half rack configuration solves a floor space problem that full power racks cannot. At 53" wide by 62" deep, this multi-function half rack occupies approximately 2.1 square meters while offering the same 3x3" 11-gauge steel construction found in racks twice its footprint. The compromise isn't structural—it's about the rack depth. By eliminating the rear uprights that full racks require, this unit allows barbell loading from the back of the rack, a feature that commercial facilities prize for traffic flow efficiency.
Originating from Shandong's commercial fitness manufacturing sector, this rack carries a 2000kg max load rating, placing it firmly in the heavy-commercial category. The 75x75x3mm tube size (approximately 3x3" with 3mm wall, slightly thicker than 11-gauge's 3.0mm) provides the section modulus necessary for rack pulls, heavy squats, and banded work without deflection. For facilities spec'ing equipment for high-volume powerlifting or CrossFit, this load rating exceeds most user requirements, ensuring the rack is never the training limitation.
The height differential is intentional. The front uprights stand at 100.375 inches (approximately 8.36 feet), accommodating tall athletes for pull-ups and overhead rack storage. The inside crossmembers connect to 90-inch rear uprights, creating an angled roofline that reduces the rack's visual mass while maintaining structural triangulation. This angled crossmember design also improves lateral stability compared to horizontal crossmembers, which can allow rack sway during banded squats or dynamic work.
The height variation serves another purpose: ceiling clearance. Many commercial facilities have dropped ceilings or HVAC obstructions at standard 8-foot heights. The 90-inch inside height fits under these obstructions while the 100-inch front section extends into open space. Facility managers should verify overhead clearance before installation, but the dual-height design offers flexibility that single-height racks cannot match.
| Dimension Parameter | Value (Imperial) | Design Implication |
|---|---|---|
| Footprint Depth | 62" (including front feet) | Stable base for heavy squats and band work |
| Footprint Width | 53" | Fits standard 48" bench with side clearance |
| Front Upright Height | 100.375" | Full pull-up ROM for tall athletes |
| Inside Height | 90" | Fits under standard 8' ceiling obstructions |
| Total Rack Depth | 30" (not including front feet) | Inside depth: 24" for barbell travel clearance |
| Tube Size | 75x75x3mm (3x3" 11-gauge equivalent) | Commercial-grade structural rigidity |
The 30" extended front feet serve two critical functions. First, they prevent forward tip during heavy squats or when athletes re-rack aggressively. Second, they provide anchor points for banded work. Each foot includes 8 laser-cut numbered holes at 1-inch diameter, allowing band pegs to be positioned for variable resistance profiles. The numbering system enables repeatable setups—an athlete can note "hole 3" and replicate the same band tension across multiple training sessions.
The extended feet also facilitate band work outside the rack, a feature half racks uniquely enable. Full racks require bands to be anchored inside the rack footprint, limiting exercise selection. With front feet extending 30" forward, athletes can anchor bands for bench pressing, standing curls, or rack pulls without interfering with the uprights. The zinc-plated band pegs (included) resist corrosion from sweat and gym cleaning chemicals.
Weight plate storage is often an afterthought in rack design, leading to clutter and safety hazards. This half rack integrates 12" plate storage posts with plastic covering on both the uprights and extended feet. The 12" length accommodates multiple bumper plates per post while the plastic covering prevents metal-on-metal contact, preserving both the plate inserts and the storage post finish.
For facilities running multiple barbells simultaneously, the storage capacity reduces the need for separate plate trees. The posts are positioned to keep the center of gravity low, preventing the rack from becoming top-heavy when loaded with 2000kg of plates. Commercial buyers should note that the black powder coat finish on the storage posts matches the rack's MG Black finish, maintaining aesthetic consistency.
| Component | Specification | Quality Indicator |
|---|---|---|
| Steel Tubing | 75x75x3mm (3x3" 11-gauge) | Heavy-commercial structural standard |
| Hardware | 1" diameter bolts | Exceeds standard 5/8" hardware |
| Finish | MG Black powder coat | Corrosion-resistant, matte finish |
| Band Pegs | Zinc-plated | Rust-resistant for high-sweat environments |
| Nameplate | Laser-cut (Rogue Red finish example shown) | Customizable for facility branding |
The product data specifies customized logo available with MOQ of 1 set, meaning even single-unit buyers can brand the rack. The reference image shows a laser-cut nameplate in Rogue Red finish, but the manufacturer—Leadman from Shandong—accepts custom logo designs for the same plate location. The plate is noted as NOT INTERCHANGEABLE, indicating it is welded or permanently fastened, not bolted for swap-out.
Customization extends beyond logos. The 1" hardware throughout indicates the rack uses heavy-duty bolts, not the smaller 5/8" hardware common on lighter racks. For facilities ordering multiple racks, the OEM capability allows for specific color matching, alternative upright heights, or modified storage post configurations. The plywood case packing protects the finish during sea freight from Qingdao Port.
The half rack design supports all standard barbell movements: back squats, front squats, bench presses (with a bench), overhead presses (standing inside the rack), rack pulls, and banded variations. The open back allows deadlifts to be performed without walking the bar through the rack—the athlete simply loads the bar behind the rack and steps in. This traffic flow efficiency matters in busy commercial facilities where multiple athletes share equipment zones.
The 24" inside depth provides sufficient room for squat walkout without feeling cramped. For comparison, competition squat racks often have 24-30" depth. The 30" total rack depth (excluding front feet) keeps the footprint compact while the extended front feet add forward stability. The 1" diameter holes in the front feet accommodate band pegs for accommodating resistance, a feature typically found only on specialty racks.
The MG Black powder coat finish is described as "more than a little better"—a claim to durability beyond standard powder coating. For commercial environments, finish quality directly correlates with corrosion resistance. Facilities near coastlines or with high humidity should prioritize racks with proven powder coat adhesion. The 2000kg max load rating suggests the structure itself is over-engineered relative to typical 500-1000kg commercial racks, providing a safety margin even when used for partial movements like rack pulls from pins.
| Specification Category | Technical Details |
|---|---|
| Place of Origin | Shandong, China |
| Product Name | Multi Function Half Rack / Power Rack |
| Type | Half Rack (open back configuration) |
| Tube Size | 75mm x 75mm x 3mm (3x3" 11-gauge equivalent) |
| Max Load Rating | 2000 kg |
| Footprint (D x W) | 62" x 53" (including front feet) |
| Total Rack Depth | 30" (not including front feet) |
| Inside Depth | 24" |
| Front Upright Height | 100.375" (approx. 8.36 ft) |
| Inside Height | 90" |
| Front Feet Extension | 30" with 8 laser-cut numbered holes (1" diameter) |
| Storage Posts | 12" length with plastic covering |
| Hardware Size | 1" bolts |
| Finish | MG Black powder coat |
| Band Pegs | Zinc-plated (included) |
| Application | Commercial Use / Body Building / CrossFit |
| Gender | Unisex |
| Packing | Plywood Case |
| Logo Customization | Available (laser-cut nameplate) |
| Minimum Order Quantity | 1 Set |
